ATCC ATCC Logo 0

Rhodoplanes cryptolactis

49414

Product category
Bacteria
Type strain
No
Product format
Freeze-dried
Storage conditions
2°C to 8°C

Documentation

Haven't found what you need?

Customize solution

We tailor our materials for your specific application.

Get application-specific materials

Biosafety Icon BSL 1

ATCC determines the biosafety level of a material based on our risk assessment as guided by the current edition of Biosafety in Microbiological and Biomedical Laboratories (BMBL), U.S. Department of Health and Human Services. It is your responsibility to understand the hazards associated with the material per your organization’s policies and procedures as well as any other applicable regulations as enforced by your local or national agencies.

ATCC highly recommends that appropriate personal protective equipment is always used when handling vials. For cultures that require storage in liquid nitrogen, it is important to note that some vials may leak when submersed in liquid nitrogen and will slowly fill with liquid nitrogen. Upon thawing, the conversion of the liquid nitrogen back to its gas phase may result in the vial exploding or blowing off its cap with dangerous force creating flying debris. Unless necessary, ATCC recommends that these cultures be stored in the vapor phase of liquid nitrogen rather than submersed in liquid nitrogen.

Detailed product information

General

Preceptrol
No

Handling information

Medium
Temperature
37°C
Atmosphere
Aerobic
Handling procedure
  1. Put 6 to 8 mL of Medium #112 into a small screw cap test tube (13x100 mm). Add 0.1 mL of 3% cysteine per each 56 mL of medium and then fill the test tube to capacity with additional Medium#112. Seal the test tube with a screw cap.
  2. Let the tube sit at room temperature for 30 minutes before inoculating it with the rehydrated culture.
  3. Open the freeze dried vial according to enclosed instructions.
  4. Aseptically take 0.5 mL of the prereduced medium and rehydrate the pellet.
  5. Transfer the rehydrated pellet back into the screw cap test tube and close tightly. (The test tube should be filled to capacity). Streak one drop of the rehydrated pellet onto Nutrient Agar (BD 213000)and/or Tryptic Soy Agar (BD 236950).
  6. Incubate the broth culture at 30°C under a tungsten lamp. Incubate the aerobic Nutrient Agar plateand/or Tryptic Soy Agar plate at 37°C in the dark.
  7. Once growth has been established (three to six days), the culture should be transferred to fresh broth. If a large inoculum is used (1020%)the medium does not need to be prereduced. Growth should be detected on the Nutrient Agar plate and/or Tryptic Soy Agar plate within 3 to 6 days.
  8. When examined microscopically, the cells are motile rods, in single and pairs. When grown in broth, the culture is pink in color.
Handling notes
This organism should be incubated in a light filled environment.
This culture is oxygentolerant, therefore strictly anoxic conditions are not required when rehydrating the freezedried pellet or transferring the organism.
Additional information on this culture is available on the ATCC® web site at www.atcc.org.

History

Deposited as
Rhodopseudomonas thermopolis
Depositors
H Gest Stadtwald-Demchick
Chain of custody
ATCC <-- H Gest Stadtwald-Demchick

Legal disclaimers

Intended use
This product is intended for laboratory research use only. It is not intended for any animal or human therapeutic use, any human or animal consumption, or any diagnostic use.
Warranty

The product is provided 'AS IS' and the viability of ATCC® products is warranted for 30 days from the date of shipment, provided that the customer has stored and handled the product according to the information included on the product information sheet, website, and Certificate of Analysis. For living cultures, ATCC lists the media formulation and reagents that have been found to be effective for the product. While other unspecified media and reagents may also produce satisfactory results, a change in the ATCC and/or depositor-recommended protocols may affect the recovery, growth, and/or function of the product. If an alternative medium formulation or reagent is used, the ATCC warranty for viability is no longer valid.  Except as expressly set forth herein, no other warranties of any kind are provided, express or implied, including, but not limited to, any implied warranties of merchantability, fitness for a particular purpose, manufacture according to cGMP standards, typicality, safety, accuracy, and/or noninfringement.

Disclaimers

This product is intended for laboratory research use only. It is not intended for any animal or human therapeutic use, any human or animal consumption, or any diagnostic use. Any proposed commercial use is prohibited without a license from ATCC.

While ATCC uses reasonable efforts to include accurate and up-to-date information on this product sheet, ATCC makes no warranties or representations as to its accuracy. Citations from scientific literature and patents are provided for informational purposes only. ATCC does not warrant that such information has been confirmed to be accurate or complete and the customer bears the sole responsibility of confirming the accuracy and completeness of any such information.

This product is sent on the condition that the customer is responsible for and assumes all risk and responsibility in connection with the receipt, handling, storage, disposal, and use of the ATCC product including without limitation taking all appropriate safety and handling precautions to minimize health or environmental risk. As a condition of receiving the material, the customer agrees that any activity undertaken with the ATCC product and any progeny or modifications will be conducted in compliance with all applicable laws, regulations, and guidelines. This product is provided 'AS IS' with no representations or warranties whatsoever except as expressly set forth herein and in no event shall ATCC, its parents, subsidiaries, directors, officers, agents, employees, assigns, successors, and affiliates be liable for indirect, special, incidental, or consequential damages of any kind in connection with or arising out of the customer's use of the product. While reasonable effort is made to ensure authenticity and reliability of materials on deposit, ATCC is not liable for damages arising from the misidentification or misrepresentation of such materials.

Please see the material transfer agreement (MTA) for further details regarding the use of this product. The MTA is available at www.atcc.org.

References

Frequently Asked Questions

Need assistance with this product? Contact our Technical Support team.

Telephone

Telephone

US and Puerto Rico

800-638-6597

Outside the US

+1-703-365-2700
hours

Hours of Operation

Monday-Friday
9:30am - 5:30pm
US Eastern Time