Trypanosoma brucei Plimmer and Bradford ATCC ® PRA-380™

Permits and Restrictions	View Permits
Strain Designations	Lister 427 procyclic form
Biosafety Level	2 Biosafety classification is based on U.S. Public Health Service Guidelines, it is the responsibility of the customer to ensure that their facilities comply with biosafety regulations for their own country.
Isolation	Unknown; possibly derived from s427 strain, Uganda, 1960
Product Format	frozen
Storage Conditions	Frozen: -70°C or colder Live Culture: See Protocols Section

Comments	Wild type procyclic form

Medium	ATCC^® Medium 2831: SDM-79 Medium ATCC^® Medium 431: Trypanosome medium
Growth Conditions	Temperature: 27°C
Cryopreservation	Harvest and Preservation Harvest cells from a culture which is at or near peak density by centrifugation at ~800 x g for 5 min. Adjust concentration of cells to 0.5–1.0 x 10⁷/mL in fresh growth medium. If the concentration is too low, centrifuge at ~800 x g for 5 minutes and resuspend the cell pellet with a volume of supernatant to yield the desired concentration. While cells are centrifuging, prepare a 20% (v/v) solution of sterile glycerol in fresh growth medium. Mix the cell preparation and the glycerol solution in equal portions. The final concentration will be 2.5-5 x 10⁶ cells/mL in 10% glycerol. The time from the mixing of the cell preparation and glycerol stock solution before the freezing process is begun should be no less than 15 min and no more than 30 min. Dispense in 0.5 mL aliquots into 1.0 - 2.0 mL sterile plastic screw-capped cryovials. Place the ampules in a Nalgene 1°C freezing apparatus. Place the apparatus at -80°C for 1.5 to 2 hours and then plunge ampules into liquid nitrogen. (The cooling rate in this apparatus is approximately -1°C/min.) If freezing unit can compensate for the heat of fusion, maintain rate at -1°C/min through heat of fusion. At -40°C, plunge ampules into liquid nitrogen. Store in either the vapor or liquid phase of a nitrogen refrigerator. To thaw a frozen ampule, place it in a 35°C water bath such that the lip of the ampule remains above the water line. Thawing time is approximately 2 to 3 minutes. Do not agitate the ampule. Do not leave ampule in water bath after it is thawed. Remove the vial from the water bath immediately after thawing. Aseptically transfer the contents of the ampule into 10 mL of fresh growth medium. Incubate the flask at 27°C with the cap screwed on tightly. Maintain as described above.

Name of Depositor	G Cross
References	Wirtz E, et al. A tightly regulated inducible expression system for conditional gene knock-outs and dominant-negative genetics in Trypanosoma brucei. Mol. Biochem. Parasitol. 99(1): 89-101, 1999. PubMed: 10215027 Cunningham MP, Vickerman K. Antigenic analysis in the Trypanosoma brucei group, using the agglutination reaction. Trans. R. Soc. Trop. Med. Hyg. 56: 48-59, 1962. PubMed: 13882652 Cross GA, Manning JC. Cultivation of Trypanosoma brucei sspp. in semi-defined and defined media. Parasitology 67(3): 315-331, 1973. PubMed: 4761771 Peacock L, et al. Fly transmission and mating of Trypanosoma brucei brucei strain 427. Mol Biochem Parasitol 160(2): 100-106, 2008. PubMed: 18524395

Name of Depositor

G Cross

References

Wirtz E, et al. A tightly regulated inducible expression system for conditional gene knock-outs and dominant-negative genetics in Trypanosoma brucei. Mol. Biochem. Parasitol. 99(1): 89-101, 1999. PubMed: 10215027

Cunningham MP, Vickerman K. Antigenic analysis in the Trypanosoma brucei group, using the agglutination reaction. Trans. R. Soc. Trop. Med. Hyg. 56: 48-59, 1962. PubMed: 13882652

Cross GA, Manning JC. Cultivation of Trypanosoma brucei sspp. in semi-defined and defined media. Parasitology 67(3): 315-331, 1973. PubMed: 4761771

Peacock L, et al. Fly transmission and mating of Trypanosoma brucei brucei strain 427. Mol Biochem Parasitol 160(2): 100-106, 2008. PubMed: 18524395

Permits	These permits may be required for shipping this product: USDA APHIS VS 16-6 or 16-6A permit must be obtained and a copy of the permit must be sent to ATCC in advance of shipment. The Application Form VS 16-3 (Import controlled material import or transport organisms or vectors) must be submitted to USDA APHIS Veterinary Services to obtain the VS 16-6 or 16-6A permit. Customer Acceptance of Responsibility, ATCC Form 62 required for distribution. Customers located in the state of Hawaii will need to contact the Hawaii Department of Agriculture to determine if an Import Permit is required. A copy of the permit or documentation that a permit is not required must be sent to ATCC in advance of shipment.
Basic Documentation	Product Sheet Certificate of Analysis SDS

Permits

These permits may be required for shipping this product:

USDA APHIS VS 16-6 or 16-6A permit must be obtained and a copy of the permit must be sent to ATCC in advance of shipment. The Application Form VS 16-3 (Import controlled material import or transport organisms or vectors) must be submitted to USDA APHIS Veterinary Services to obtain the VS 16-6 or 16-6A permit.
Customer Acceptance of Responsibility, ATCC Form 62 required for distribution.
Customers located in the state of Hawaii will need to contact the Hawaii Department of Agriculture to determine if an Import Permit is required. A copy of the permit or documentation that a permit is not required must be sent to ATCC in advance of shipment.

Basic Documentation